امروز : جمعه , ۲۴ مرداد ۱۳۹۹

ATrack AU5i

معرفی دستگاه

این محصول توسط ATrack تولید شده است و در گروه AVL Hardware قرارداد.

odometer
Built-in odometer
adc
ADC sensors
gprs_req
Remote management via GPRS
ibutton
Driver identification
inputs
Digital sensors
lbs
LBS
tcp
Communication via TCP
pwr_ext (V)
Voltage of external power supply
pwr_int (V)
Power supply internal battery
gsm
GSM signal quality
pulse_count
Pulse count value
engine_rpm
Engine RPM reading
gsm_status
GSM status
dt
0-Real time report
mf
Mass Air Flow Rate in 0.01grams/sec
el (%)
Engine Load
tr (%)
Throttle position
ml
MIL (Malfunction Indicator Lamp) status
coolant_temp (°C)
Engine Coolant Temperature
fuel_level (%)
Fuel Level
fuel_consumption
Fuel Used in 0.1 liter
analog_volt
Analog voltage reading
max_speed
Maximum speed between two reports
gl
Google Link (N/A in AX5)
gx (0.0098*m/s)
X-axis acceleration
gy (0.0098*m/s)
Y-axis acceleration
gz (0.0098*m/s)
Z-axis acceleration
motion
Vehicle motion event status
engine
Engine event status
Model Name:
Device Model Name
Firmware Ver:
Device firmware version information
IMEI:
International Mobile Equipment Identity number (Not available in AY5(i); 0 is shown)
IMSI:
International Mobile Subscriber Identity (Not available in AY5(i); 0 is shown)
CID:
Card identification number of SIM card (Not available in AY5(i); 0 is shown)
Main Volt: (V)
Main power voltage in 0.1
Battery Volt: (V)
Backup battery voltage in 0.1
SATS:
Numbers of GPS satellite currently used
GSM Status:
GSM Network registration status (Not available in AY5(i); 0 is shown):
0: Network not registered
1: Registered to home network
2: Searching for available network
3: Registration denied
4: Un
GPS Status:
GPS antenna status:
Bit 0: 0 -> GPS antenna connected
          1 -> GPS antenna disconnected
Bit 1: 0 -> GPS antenna cable OK
          1 -> GPS antenna cable sho
tracking_mode
The GPS tracking Mode parameter can be in conjunction with the following bits:
Bit 0: Time mode
Bit 1: Distance mode
Bit 2: ACC status (Must combine with Bit 0 or Bit 1)
Bit 3: Heading change condition
min_send_time
Minimum time in seconds that must elapse before reporting next position. (Min. 1 seconds)
min_send_dist
Minimum distance in multiple of 10 meters that must be traveled before reporting next position. (Min. 20 meters)
min_heading
Minimum heading in degree that must be changed before reporting next position. (15..180)
min_speed
Minimum speed in km/h that must be achieved before reporting next position.
track_times
Specify tracking times. =0 means forever tracking.
dest_type
Specify the destination for tracking report position The parameter is in conjunction with the following bits:
0: Default communication type. (i.e. Command issuer)
Bit 0: SMS
Bit 1: GPRS (This is the only option for A
sched
Specify the schedule for the report. The parameter is in conjunction with the following bits:
0 – indicates use no schedule (i.e. always on)
Bit 0 – Schedule 1
Bit 1 – Schedule 2
Bit 2 – Schedule 3
acc_off_time
Minimum time in seconds that must elapse before reporting next position while the ACC is in Off status. ACC status in Mode must be set in order to use this time interval. (Min. 1 seconds)
coll_num
Number of position to be put into one TCP/UDP packet
temp_a_id
The sensor ID corresponding to temperature A
curr_a_temp
The temperature reading from sensor ID A
temp_b_id
The sensor ID corresponding to temperature B
curr_b_temp
The temperature reading from sensor ID B
sensor_index
The connected port number where the Temperature Sensor connected with by different user.
1: First detected sensor
2: Second detected sensor
min_temp (°C)
Minimum temperature value, and is in 0.1
max_temp (°C)
Maximum temperature value, and is in 0.1
hold_duration
A temperature holding time, and is in minute unit.
sensor_id
Temperature sensor ID. This temperature sensor can be set to be index 1 or 2 by specifying the ID in this field.
status
Current status of RPM over-revving event
0: RPM (Engine over-revving) OFF
1: RPM (Engine over-revving) ON
rpm_value
RPM value for each pulse.
current_rpm
Current RPM reading
vss_value
VSS value is total pulses for 1 kilometer.
rpm_on_tresh
RPM for detecting RPM (Engine over-revving) ON state.
on_duration
Duration in seconds that must elapse before RPM (Engine over-revving) state change is accepted.
rpm_off_tresh
RPM for detecting RPM (Engine over-revving) OFF state.
off_duration
Duration in seconds that must elapse before RPM (Engine over-revving) state change is accepted.
fuel_cons (l/h or km/)
Fuel Consumption
eng_boost_pressure (kPa)
Engine Turbocharger Boost Pressure
intake_manifold_temp (°C)
Engine Intake Manifold 1 Temperature
eng_load (%)
OBD Calculated engine load
accel_pos (%)
Accelerator pedal
trottle_pos (%)
Throttle Position
cargo_weight (N)
Cargo Weight
brake_app_pressure (kPa)
Brake Application Pressure
brake_pressure1 (kPa)
Brake Primary Pressure
brake_pressure2 (kPa)
Brake Secondary Pressure
brake_times
Brake Switch apply times
clutch_times
Clutch Switch apply times
cruise_time (second)
Time Cruise active
abs_time (second)
Time ABS Active
parking_brake (0/1)
Parking Brake Switch Status
intake_air_temp (°C)
OBD Intake air temperature
trootle_pos (%)
OBD Throttle position
mil_on_status (0/1)
OBD MIL ON (Engine Fault) Status
maf_air_rate (g/s)
OBD MAF air flow rate
axle1-4 (kg)
Axle weight
intake_manifold_air_temp (°C)
Engine Intake Manifold 1 Temperature
pt_air_pressure (kPa)
Parking and/or Trailer Air Pressure
brake_pressure1-2 (kPa)
Service Brake Air Pressure Circuit 1-2
drivers_state
Driver1/2 Working State
driver1-2_card
Driver1-2 Card status & time related state
tachograph_status
Tachograph Overspeed status
tacho_ext_info
Direction, Tachograph performance, handling info, system event
cango_
CANGO FMS parameter
gps_tm (s)
GPS Time. Unix Timestamp
rtc_tm (s)
RTC Time. Unix Timestamp
snd_tm (s)
Position Sending Time. Unix Timestamp
prf
Message prefix